- Features & Specs
- More Info
The Atlas Pro-9D is the perfect choice for those customers who demand the most lifting capacity at the lowest possible price. The Atlas Pro-9D can be adjusted to two different height settings: 11' 6" or 11' 10".
The Atlas Pro-9D has symmetric columns and specially designed arms that can be set in either the symmetric or asymmetric position. The asymmetric/symmetric arm design offers an extremely low lift pad position on the EZ-metric lift arm configuration. This low pad height will allow the operator to position the lift arms under most small cars (with low pick up points) and heavier pick up trucks.
The Atlas Pro-9D includes: a complete set of solid peg type truck adapters, mounting hardware, a set of sliding lift point adapters, and a 220 volt single phase power unit that can be mounted on either side of the lift. (The power unit column must be on the correct side).
The Atlas Pro-9D two post direct drive cylinder lifts have a spring loaded Secondary Lock System (SLS) that automatically engages in the event of a slack or broken chain.
Single Point Lock Release - This Atlas Lift has a manual single point lock release that allows the operator to release all the safety locks at one time. The spring loaded lock handle and power unit dump valve must be activated at the same time. (two hand operation) If the lock handle is released and the dump valve handle is still being pressed, the lift will continue to descend and all locks will automatically re-engage at the next lower lock point.
Automatic Arm Restraints - are needed to keep the arm "locked" into a position relative to the carriage. When the arms are at rest in the lowest position, the arm restraint pin (which extends below the carriage) is pressed up and the lock (teeth) mechanism is disengaged. The operator can then move the arms so that the lift pads can be properly positioned under the vehicle’s lift points. Once the carriage is raised (approximately 2 inches) the lock is reengaged and the arms cannot be moved. However, the operator may pull the knob or metal ring to manually unlock the arms. Lock restraints do not guarantee that a vehicle cannot be "moved" off of the lift pads. Operator should use care when working on vehicles that have an abundant amount of undercoating (lift pads may "slide") or a significant weight imbalance of the vehicle may occur due to removal of an engine or transmission. Also, "HEAVY wrenching" may result in a vehicle shifting weight on the arm pads. We recommend the use of tall jack stands under the vehicle to add another layer of safety.
Overhead Configuration - The overhead bar configuration leaves the floor area between the columns open, and allows the operator to easily roll a transmission jack or a tool box under the car. The Automatic Padded Shut-Off Bar located below the cross beam prevents the top of the vehicle from being damaged by hitting the cross beam. The padded bar, which contacted automatically shuts off the motor on the power unit to prevent the vehicle from being lifted.
Asymmetric/Symmetric Arm Design - offers an extremely low lift pad position on the EZ-metric lift arm configuration. This low pad height will allow the operator to position the lift arms under most small cars (with low pick up points) and heavier pick up trucks. This lift has symmetrical columns and includes a set of EZ-metric arms. These arms can be configured into the symmetrical position to lift a full loaded pick up truck OR these arms can be configured to the asymmetric position to offer easier opening of the front door on some vehicles.
Features & Specs
- 9,000 LB. Capacity
- Light Commercial Grade
- "Padded" Shut-Off Bar
- Asymmetric/Symmetric Arms
- Clear Floor Design
- Powder Coat Finish
- Dual Hydraulic Direct Drive Cylinders
- Single Point Lock Release
- Secondary Lock System (SLS)
- Free 8 Piece Truck Adapter Set
- Automatic Arm Restraints
- Mounting Hardware Included
- 5-year Structural Warranty, 2-year Hydraulic-Power Warranty
- Capacity: 9,000 lbs.
- Overall Height: 142" (11' 10")
- Overall Width (With Power Unit): 140" (11' 8")
- Overall Width (Without Power Unit): 132" (11')
- Outside Column To Outside Column: 122-1/2" (10' 2-1/2")
- Maximum Lift Height (Without Adapters): 77-5/8" (6' 5-5/8")
- Maximum Lift Height (With Adapters): 82-5/8" (6' 10-5/8")
- Padded Bar Height: 134-1/4" (11' 2-1/4")
- Minimum Arm Height: 4-1/2"
- Inside Column: 110-1/4" (9' 2-1/4")
- Column Size: 7-1/4" x 11"
- Drive Thru (Symmetric Arm Configuration): 98" (8' 2")
- Drive Thru (Asymmetric Arm Configuration): 88-3/4" (7' 4-3/4")
- Base of Lift: 14-1/2" x 18"
- Column Thickness of Steel: 5mm
- Carriage Thickness of Steel: 6mm
- Arms Thickness of Steel: 6mm
- Cable Diameter: .375"
- Motor Requirement: 220V Single (1) Phase
- Electrical Requirement: A 30 Amp Breaker is Required
- Floor Requirement: Minimum 4" 3000PSI Concrete
- Oil Requirement: 3-5 Gallons AW32/AW46
- Shipping Weight: 1450 lbs.
5 Year Structural & 2 Year Hydraulic Warranty
This Atlas product is warranted for five (5) years on structural components two (2) years on hydraulics, and one (1) year on electric or air / hydraulic power units effective from date of invoice. Wear items carry a 90 day warranty. Wear items carry a 90-day warranty. Structural components are considered the Carriage, Columns, Yokes, Arms, Runways, Plungers, etc. Hydraulic components are cylinders, hoses, and fittings. Cables, sheaves, latches and controls are considered wear items.
Our LIMITED warranty policy does not include a labor warranty. Our products are sold at such a competitive price that we cannot afford to send technicians into the field to repair the Atlas equipment. We assume that the buyer of our automotive equipment is mechanically inclined or has employees that are mechanically inclined to perform essential repair services and or maintenance. We also have a list of service technicians that can come to your facility/house at the customer's expense.
NOTE: ALL WARRANTY CLAIMS MUST BE PRE-APPROVED BY THE MANUFACTURER TO BE VALID.
The electric motor for the power unit requires 220 Volt (single phase) 60 Hz (+/- 5%, so 209-231 volts). We recommend using at least a 10 gauge (grounded) wire from the electrical panel. The power unit may or may not have a short pigtail (no plug) that can be wired to either an optional quick disconnect box (mounted on the lift column) or to a male/female plug combination. A 30 amp breaker is required.
The Atlas Pro-9D Overhead Two Post Lift should be installed on a concrete floor. This concrete floor should have a minimum of four (4) inches of concrete with 3000 PSI strength. Most of our above ground lift customers install their own car lifts. The average time to install the Atlas Pro-9D car lift is five hours. We provide detailed installation instructions with all our two post above ground lifts and our four post above ground lifts.
Atlas Pro-9D Overhead Two Post Lift Reviews
Add your review